Just How to Install a Bathtub: Set Up an Acrylic Tub and Bathtub Surround
Just How to Install a Bathtub: Set Up an Acrylic Tub and Bathtub Surround
Blog Article
Presented here in the next paragraph you can find a bunch of helpful help and advice in regards to How to Install a Bathtub: Install an Acrylic Tub and Tub Surround.
Mounting a bathtub isn't precisely brain surgery, but it does require solid plumbing, woodworking, and also sometimes, tiling skills. Changing an old bathtub with a new one is also a moderately tough task. If the old bathtub is readily accessible, the job can move immediately; if you need to open a wall to eliminate the old bathtub and also place the brand-new bath tub, the job is a lot harder. In either situation, the project is within a home handyman's skills, although you will need a helper to vacate the old bathtub and also embeded in the brand-new one. Make sure you have qualified yourself for the job and are comfortable attempting it. As opposed to employing a service provider to take control of a halfway-completed project, it is better to consider employing one before you begin. Possibilities are you might need a professional plumber to make tube links.
This write-up will certainly aid you mount a new bathtub in your bathroom if you have already purchased a new tub and don't need to change the plan of your previous supply of water pipes.
Your tools as well as material checklist ought to consist of the following:
Removing Old Taps
If you require to change old faucets with brand-new ones as a part of your setup, then the first thing you ought to do is disconnect the supply of water. After doing so, turn on the taps to drain pipes any kind of water remaining in the system. The process of removing the existing taps can be quite bothersome because of the restricted access that is usually the situation.
Utilize a basin wrench (crowsfoot spanner) or a faucet device to undo the nut that connects the supply pipelines to the faucets. Have a fabric ready for the continuing to be water that will certainly originate from the pipes. Once the supply pipelines have actually been eliminated, use the very same device to loosen the nut that holds the faucets onto the bath/basin. You will need to quit the solitary taps from transforming during this procedure. When the taps have actually been gotten rid of, the holes in the bath/basin will need to be cleaned of any old securing compound.
Before going on to fit the new faucets, contrast the pipe links on the old faucets to the new faucets. If the old faucets are longer than the brand-new taps, then a shank adapter is needed for the new faucets to fit.
Suitable New Taps
If the tails of the brand-new taps are plastic, then you will certainly need a plastic adapter to prevent damages to the string. One end of the port fits on the plastic tail of the tap and also the other end gives a link to the existent supply pipelines.
If you need to fit a monobloc, after that you will call for decreasing couplers, which attaches the 10mm pipeline of the monobloc to the basic 15mm supply pipe.
Next off, position the faucet in the mounting hole in the bath/basin making certain that the washers remain in area between the faucet and the sink. Safeguard the tap in place with the supplier offered backnut. As soon as the tap is firmly in place, the supply pipelines can be connected to the tails of the faucets. The taps can either be connected by using corrugated copper piping or with regular tap adapters. The previous kind should be linked to the faucet finishes initially, tightening only by hand. The supply pipes can later be linked to the various other end. Tighten up both ends with a spanner after both ends have been attached.
Installing the Bathtub
Using the two wood boards under its feet, position the bath tub in the called for position. The wooden boards are useful in uniformly spreading the weight of the bathtub over the area of the boards rather than focusing all the weight onto four little factors.
The next goal is to make certain that the bathtub is leveled all round. This can be accomplished by examining the spirit level and also adjusting the feet on the tub till the spirit level checks out degree.
To mount faucets, fit the bottom of the furthest adaptable faucet connector to the proper supply pipeline by making a compression join; after that do the same for the other tap.
Activate the water and inspect all joints as well as brand-new pipework for leakages and tighten them if required. Fill up the bath tub and likewise examine the overflow electrical outlet and the normal outlet for leakages.
Ultimately, deal with the bath paneling as described in the producer's instruction manual. Tiling and sealing around the bathtub ought to wait until the bathtub has been used at least when as this will certainly resolve it right into its last placement.
Preparing for the Installation
Firstly, the supporting framework provided with the bathroom needs to be fitted (if called for) according to the supplier's guidelines. Next off, fit the taps or mixer to the tub. When fitting the tap block, it is essential to make sure that if the faucet comes with a plastic washing machine, it is fitted in between the bathroom and also the faucets. On a plastic bathroom, it is likewise practical to fit a supporting plate under the taps device to stop stress on the bath tub.
Fit the versatile tap connectors to the bottom of both faucets utilizing 2 nuts and olives (sometimes provided with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet opening, and after that pass the electrical outlet with the hole in the bathroom. Utilize the nut supplied by the producer to fit the plug-hole. Analyze the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next off, fit completion of the flexible overflow pipeline to the overflow outlet. After that, screw the pipeline to the overflow face which must be fitted inside the bath. Ensure you use every one of the supplied washers.
Attach the trap to the bottom of the waste outlet on the bath tub by winding the thread of the waste outlet with silicone mastic or PTFE tape, and screw on the trap to the electrical outlet. Link the bottom of the overflow tube in a comparable manner.The bathroom need to currently be ready to be fitted in its last setting.
Tiling Around the Bathtub
In the location where the bathroom satisfies the tile, it is essential to seal the joins with a silicone rubber caulking. This is necessary as the installation can relocate enough to fracture a stiff seal, causing the water to pass through the wall between the bathroom as well as the tiling, leading to issues with dampness and also possible leaks to the ceiling listed below.
You can pick from a range of coloured sealers to assimilate your fixtures and also fittings. They are marketed in tubes and cartridges, and also are capable of sealing voids as much as a size of 3mm (1/8 inch). If you have a larger void to fill up, you can load it with twists of drenched newspaper or soft rope. Remember to constantly fill the tub with water prior to sealing, to permit the movement experienced when the tub remains in use. The sealer can crack relatively very early if you do not take into consideration this movement prior to securing.
Additionally, ceramic coving or quadrant floor tiles can be used to edge the bath or shower tray. Plastic strips of coving, which are easy to use and also cut to dimension, are also quickly readily available on the market. It is suggested to fit the tiles making use of water-resistant or water resistant glue as well as grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
We were introduced to that editorial on Tools You Need to Install a New Bathtub through an associate on a different web page. Are you aware of somebody who is interested in How to Install a Bathtub Yourself? Feel free to share it. Thanks for going through it.
Visit My Website
Report this page